>
News | Archive
NewsArchive
Click on any of the press release below to find out more about what's going on in the world of DYNAenergetics:
TROUBLE SHOOTING GUIDE
This is a list of FAQs concerning the handling of DYNAWELL Oiltronic and Multitronic Firing Panels. Find solutions for frequent appearing problems: [more...]
This is a list of FAQs concerning the handling of DYNAWELL Oiltronic and Multitronic Firing Panels. Find solutions for frequent appearing problems: [more...]
TECHNICAL BULLETIN #09080501:
Shaped Charge 23g BH released
With its new 23 g BH DYNAenergetics has completed the development of the 23g Charge range. The 23g shaped charges has the same outside charge case configuration as the current 23g DP and 23g GH shaped charges, as well as the unsurpassed 23g DPEX reactive linder shaped charge. For our customers this means a decrease in gun inventory and an increase in flexibility, as all of the 23g shaped charges can be used in the same gun systems. [more...]
Shaped Charge 23g BH released
With its new 23 g BH DYNAenergetics has completed the development of the 23g Charge range. The 23g shaped charges has the same outside charge case configuration as the current 23g DP and 23g GH shaped charges, as well as the unsurpassed 23g DPEX reactive linder shaped charge. For our customers this means a decrease in gun inventory and an increase in flexibility, as all of the 23g shaped charges can be used in the same gun systems. [more...]
NEW UN DIRECTIVE FOR TRANSPORT
1.4 S Classification
Please be advised that DYNAenergetics has been informed by their competent authority and major freight forwarders that effective immediately a new UN directive is in effect concerning the transport of 1.4S classified product on passenger air craft. [more...]
1.4 S Classification
Please be advised that DYNAenergetics has been informed by their competent authority and major freight forwarders that effective immediately a new UN directive is in effect concerning the transport of 1.4S classified product on passenger air craft. [more...]
TECHNICAL BULLETIN #08112501:
Current Setting with Multitronic II Firing Panel
The Multitronic II Firing Panel has been used in the perforating industry for several years. Unfortunately it seems that there is still some confusion in regards to the Voltage Adjustment and Current Settings in the software. This technical bulletin describes a recommended practise to set up the software adjustable parameters. [more...]
Current Setting with Multitronic II Firing Panel
The Multitronic II Firing Panel has been used in the perforating industry for several years. Unfortunately it seems that there is still some confusion in regards to the Voltage Adjustment and Current Settings in the software. This technical bulletin describes a recommended practise to set up the software adjustable parameters. [more...]
TECHNICAL BULLETIN #08111801:
Welcome Mr. Ihab Ismail to the international DYNAenergetics sales team
With its core values including customer satisfaction and global growth DYNAenergetics is expanding the international sales network. Please join us in welcoming Mr. Ihab Ismail to the international DYNAenergetics sales team. He has been named in the position of Sales Manager Middle East and will be working out of his office in Abu Dhabi. [more...]
Welcome Mr. Ihab Ismail to the international DYNAenergetics sales team
With its core values including customer satisfaction and global growth DYNAenergetics is expanding the international sales network. Please join us in welcoming Mr. Ihab Ismail to the international DYNAenergetics sales team. He has been named in the position of Sales Manager Middle East and will be working out of his office in Abu Dhabi. [more...]
TECHNICAL BULLETIN #08101701
EIST Test Report
As a result of many customer complaints from the field and our own intensive analysis of the electronic igniter for setting tool, it was decided that a re-design of the contact assembly and crimping mechanisms was absolutely essential in order to provide a reliable product which functioned fail-safe. The electronic components of the igniter were not changed in any way so that none of the RF safety functions of the igniter would be compromised. The following is a list of the problems which existed within our old design of the EIST which needed to be corrected. [more...]
EIST Test Report
As a result of many customer complaints from the field and our own intensive analysis of the electronic igniter for setting tool, it was decided that a re-design of the contact assembly and crimping mechanisms was absolutely essential in order to provide a reliable product which functioned fail-safe. The electronic components of the igniter were not changed in any way so that none of the RF safety functions of the igniter would be compromised. The following is a list of the problems which existed within our old design of the EIST which needed to be corrected. [more...]
TECHNICAL BULLETIN #08061201
MODIFICATION OF MULTITRONIC II FIRING PANEL
TO ENHANCE THE FUNCTIONALITY OF THE VOLTAGE CALIBRATION SEQUENCE OF THE MULTITRONIC II FIRING PANEL A HARDWARE MODIFICATION HAS BEEN MADE. [more...]
MODIFICATION OF MULTITRONIC II FIRING PANEL
TO ENHANCE THE FUNCTIONALITY OF THE VOLTAGE CALIBRATION SEQUENCE OF THE MULTITRONIC II FIRING PANEL A HARDWARE MODIFICATION HAS BEEN MADE. [more...]
TECHNICAL BULLETIN #08061203
CHANGE OF RESET TIME
THE USE OF THE MULTITRONIC RF-SAFE SELECTIVE PERFORATING SYSTEM AT LOW TEMPERATURES (-10°C / 14°F) HAS BROUGHT TO OUR ATTENTION THAT THE RESET TIME OF THE SOFTWARE IS NOT LONG ENOUGH WHEN THE SYSTEM IS EXPOSED TO THESE CONDITIONS. [more...]
CHANGE OF RESET TIME
THE USE OF THE MULTITRONIC RF-SAFE SELECTIVE PERFORATING SYSTEM AT LOW TEMPERATURES (-10°C / 14°F) HAS BROUGHT TO OUR ATTENTION THAT THE RESET TIME OF THE SOFTWARE IS NOT LONG ENOUGH WHEN THE SYSTEM IS EXPOSED TO THESE CONDITIONS. [more...]
TECHNICAL BULLETIN #08012601:
Use of USB to RS232 Adapter with Multitronic Panel II
Due to the rapid developments in computer technology the use of RS232 ports has been largly replaced vy USB ports. [more...]
Use of USB to RS232 Adapter with Multitronic Panel II
Due to the rapid developments in computer technology the use of RS232 ports has been largly replaced vy USB ports. [more...]
TECHNICAL BULLETIN #06080301
No Debris Gun System
Perforating jobs traditionally leave a lot of unwanted debris in the well. The interior of the perforating guns and the cases of the shaped charges are fragmented during the shot. Up to several hundred gram/shot can be left in the well. [more...]
No Debris Gun System
Perforating jobs traditionally leave a lot of unwanted debris in the well. The interior of the perforating guns and the cases of the shaped charges are fragmented during the shot. Up to several hundred gram/shot can be left in the well. [more...]
TECHNICAL BULLETIN #04110301
Production Facilities Hardware
DYNAenergetics IS PROUD TO ANOUNCE THAT OUR PRODUCTION FACILITY FOR HARDWARE IN TROISDORF IS NOW OPERATIONAL. [more...]
Production Facilities Hardware
DYNAenergetics IS PROUD TO ANOUNCE THAT OUR PRODUCTION FACILITY FOR HARDWARE IN TROISDORF IS NOW OPERATIONAL. [more...]
TECHNICAL BULLETIN #04110302
Booster Kit DYNAWELL
DYNAenergetics IS PROUD TO ANOUNCE THE DEVELOPMENT OF A ONE SIZE FOR ALL BOOSTER KIT THAT CAN BE USED UNIVERSALLY IN ALL OF THE GUN SYSTEMS DYNAWELL FROM 70 mm to 114 mm MANUFACTURED BY DYNAenergetics. [more...]
Booster Kit DYNAWELL
DYNAenergetics IS PROUD TO ANOUNCE THE DEVELOPMENT OF A ONE SIZE FOR ALL BOOSTER KIT THAT CAN BE USED UNIVERSALLY IN ALL OF THE GUN SYSTEMS DYNAWELL FROM 70 mm to 114 mm MANUFACTURED BY DYNAenergetics. [more...]
TECHNICAL BULLETIN #04082501
X-RAY OF AIR GAP BETWEEN BOOSTER AND DETONATING CORD
IN CERTAIN INSTANCES IT HAS BEEN OBSERVED THAT BOOSTERS WERE CRIMPED ONTO THE DETONATING CORD WITH AIR GAPS BETWEEN THE BOOSTER EXPLOSIVE COLLUM AND THE DETONATING CORD END. DEPENDING ON THE LENGTH OF THE AIR GAP THIS CAN LEAD TO A MISFIRE. [more...]
X-RAY OF AIR GAP BETWEEN BOOSTER AND DETONATING CORD
IN CERTAIN INSTANCES IT HAS BEEN OBSERVED THAT BOOSTERS WERE CRIMPED ONTO THE DETONATING CORD WITH AIR GAPS BETWEEN THE BOOSTER EXPLOSIVE COLLUM AND THE DETONATING CORD END. DEPENDING ON THE LENGTH OF THE AIR GAP THIS CAN LEAD TO A MISFIRE. [more...]
TECHNICAL BULLETIN #04082502
X-RAY OF DETONATING CORD
IN CERTAIN INSTANCES STOPFIRES IN PERFORATING GUNS HAVE BEEN OBSERVED. ONE POSSIBLE CAUSE FOR MISFIRES ARE MANUFACTURING DEFECTS INSIDE THE DETONATING CORD WHICH CAN NOT BE SEEN FROM THE OUTSIDE. [more...]
X-RAY OF DETONATING CORD
IN CERTAIN INSTANCES STOPFIRES IN PERFORATING GUNS HAVE BEEN OBSERVED. ONE POSSIBLE CAUSE FOR MISFIRES ARE MANUFACTURING DEFECTS INSIDE THE DETONATING CORD WHICH CAN NOT BE SEEN FROM THE OUTSIDE. [more...]
TECHNICAL BULLETIN #04082401
NEW 1.1D and 1.4S DETONATING CORD PACKAGING
AS AN EXPLOSIVE PRODUCTS MANUFACTURER WE ARE GIVING YOUR SAFETY OUR HIGHEST PRIORITY. FOR YOUR CONVENIENCE WE HAVE STANDARDIZED ALL OF THE DETONATING CORD PACKAGING. [more...]
NEW 1.1D and 1.4S DETONATING CORD PACKAGING
AS AN EXPLOSIVE PRODUCTS MANUFACTURER WE ARE GIVING YOUR SAFETY OUR HIGHEST PRIORITY. FOR YOUR CONVENIENCE WE HAVE STANDARDIZED ALL OF THE DETONATING CORD PACKAGING. [more...]
TECHNICAL BULLETIN #04060401
PACKAGING CHANGE FOR FLUID DISABLED DETONATORS 0015FD, 0026FD, 0015FDE AND 0026FDE
IN CERTAIN ENVIRONMENTAL CONDITIONS FOR PROLONGED PERIODS OF TIME THE EXPOSEURE OF THE UNSEALED FLUID DISABLED DETONATORS CAN HAVE ADVERSE EFFECTS ON THE FUSE HEAD WHICH CAN LEAD TO A MISFIRE. [more...]
PACKAGING CHANGE FOR FLUID DISABLED DETONATORS 0015FD, 0026FD, 0015FDE AND 0026FDE
IN CERTAIN ENVIRONMENTAL CONDITIONS FOR PROLONGED PERIODS OF TIME THE EXPOSEURE OF THE UNSEALED FLUID DISABLED DETONATORS CAN HAVE ADVERSE EFFECTS ON THE FUSE HEAD WHICH CAN LEAD TO A MISFIRE. [more...]
